diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h
new file mode 100644
index 0000000..41330e9
--- /dev/null
+++ b/include/configs/SMN42.h
@@ -0,0 +1,198 @@
+/*
+ * (C) Copyright 2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Configuation settings for the SMN42 board from Siemens.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start u-boot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#undef CONFIG_INIT_CRITICAL		/* undef for developing */
+
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_ARM7		1	/* This is a ARM7 CPU	*/
+#define CONFIG_ARM_THUMB	1	/* this is an ARM720TDMI */
+#define CONFIG_LPC2292
+#undef  CONFIG_ARM7_REVD	 	/* disable ARM720 REV.D Workarounds */
+
+#undef CONFIG_USE_IRQ			/* don't need them anymore */
+
+/*
+ * Size of malloc() pool
+ */
+#define CFG_MALLOC_LEN		(CFG_ENV_SIZE + 128*1024)
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1		1	/* we use Serial line 1 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+/* enable I2C and select the hardware/software driver */
+#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+/* this would be 0xAE if E0, E1 and E2 were pulled high */
+#define CFG_I2C_SLAVE		0xA0
+#define CFG_I2C_EEPROM_ADDR	(0xA0 >> 1)
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */
+#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+/* not used but required by devices.c */
+#define CFG_I2C_SPEED 10000
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define SCL		0x00000004		/* P0.2 */
+#define SDA		0x00000008		/* P0.3 */
+
+#define	I2C_READ	((GET32(IO0PIN) & SDA) ? 1 : 0)
+#define	I2C_SDA(x)	{ if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); }
+#define	I2C_SCL(x)	{ if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); }
+#define	I2C_DELAY	{ udelay(100); }
+#define	I2C_ACTIVE	{ unsigned int i2ctmp; \
+ 					  i2ctmp = GET32(IO0DIR); \
+					  i2ctmp |= SDA; \
+					  PUT32(IO0DIR, i2ctmp); }
+#define	I2C_TRISTATE	{ unsigned int i2ctmp; \
+ 					      i2ctmp = GET32(IO0DIR); \
+					      i2ctmp &= ~SDA; \
+						  PUT32(IO0DIR, i2ctmp); }
+#endif /* CONFIG_SOFT_I2C */
+
+/*
+ * Supported commands
+ */
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_FAT		| \
+				CFG_CMD_MMC		| \
+				CFG_CMD_NET		| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_PING)
+
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY	5
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_PROMPT		"SMN42 # " /* Monitor Command Prompt	*/
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x81800000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x83000000	/* 24 MB in SRAM	*/
+
+#undef  CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
+
+#define	CFG_LOAD_ADDR		0x81000000	/* default load address	for uClinux img is here*/
+
+#define CFG_SYS_CLK_FREQ        58982400        /* Hz */
+#define	CFG_HZ			2048		/* decrementer freq in Hz */
+
+						/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	1	   /* we have 1 bank of SRAM */
+#define PHYS_SDRAM_1		0x81000000 /* SRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE	0x02000000 /* 32 MB SRAM */
+
+/* This is the external flash */
+#define PHYS_FLASH_1		0x80000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE		0x01000000 /* 16 MB */
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/*
+ * The first entry in CFG_FLASH_BANKS_LIST is a dummy, but it must be present.
+ */
+#define CFG_FLASH_BANKS_LIST	{ 0, PHYS_FLASH_1 }
+#define CFG_FLASH_ADDR0			0x555
+#define CFG_FLASH_ADDR1			0x2AA
+#define CFG_FLASH_ERASE_TOUT	16384	/* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT	5	/* Timeout for Flash Write (in ms) */
+
+#define CFG_MAX_FLASH_SECT	128  /* max number of sectors on one chip    */
+
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+/* The Environment Sector is in the CPU-internal flash */
+#define CFG_FLASH_BASE		0
+#define CFG_ENV_OFFSET		0x3C000
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + CFG_ENV_OFFSET)
+#define CFG_ENV_SIZE		0x2000 /* Total Size of Environment Sector	*/
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_MMC			1
+/* we use this ethernet chip */
+#define CONFIG_ENC28J60
+
+#endif	/* __CONFIG_H */